Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
What're your ideas concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open a wall surface to remove the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have certified yourself for the work and are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This short article will certainly aid you mount a brand-new bathtub in your bathroom if you have already purchased a new bathtub and do not need to transform the setup of your previous supply of water pipelines.
Your tools as well as material list should comprise the following:
Planning for the Installation
To start with, the sustaining frame supplied with the bath must be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic due to the restricted accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wooden boards under its feet, position the bath tub in the required placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bathtub until the spirit level checks out degree.
To install faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the water and examine all joints and also new pipework for leakages and also tighten them if necessary. Load the tub and additionally check the overflow outlet as well as the regular outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bath tub has been utilized at least once as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washers are in location between the faucet as well as the sink. Secure the tap in position with the producer offered backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, creating the water to permeate the wall surface between the bath and the tiling, causing problems with moisture and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, and also can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break fairly early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about Tools You Need to Install a New Bathtub , I assumed sharing that piece of content was smart. For those who liked our article plz remember to pass it around. I treasure reading our article about Installing A Bathtub.
Emergency action? Dial here. Report this page